Jump to content

fundak

Member
  • Posts

    8
  • Joined

  • Last visited

fundak's Achievements

(2/3)

  1. I checked stage displays again, and there is no two display names alike. I also checked empty space in show to be sure if there is nothing left there. To make it more clear it looks like this: Cluster 1 (it has no name set in Preferences/General) Display Names: D1.1; D1.2; D2.1; D2.2; D3.1; D3.2; D4.1; D4.2 (8 displays) Cluster 2 (no name set in Preferences/General) Display Names: G1; G2; G3; G4; G5; D1; D2; D3; D4; D5; L-G1; L-G2; L-G3; L-G4; L-G5; L-D1; L-D2; L-D3; L-D4; L-D5; S1; S2 (22 displays) How can I see which computer is master for cluster?
  2. It's strange because each display in both cluster has uniqe name. First cluster consists of 2 computers (8 displays- named D1.1; D1.2 ... D4.1; D4.2), second of 6 computer (22 displays named G1 ... G5; D1 ... D5; L-G1 ... L-G5; L-D1 ... L-D5; S1; S2). Each computer has different IP adress. Is there any other place in watchout configuration where the conflict can occur? I don't have cluster name and cluster IP prefix set.
  3. Hi, I have encountered a problem with Watchout. I have two instalations on one object (two separate computer clusters in one museum). I'm using TCP/IP commands to control it (basicly it's just load and play). The problem is that the first show is starting ok, but second one ONLY is the first one is turned on. When I start second show without first one, it goes through authenticate 1, it successfuly loads show, but it stops at run command- It displays not applicable in current state. If first cluster is running- second runs also. Watchout 5.5.1 Is it a problem with TCP control, or with show itself?
  4. Hi, I'm trying to make custom PC for displaying movie with two WUXGA projectors. I searched forum to find something, but all I could find was usualy for 4 or more outputs. Since my setup is not event solution and I computer will be there for good, I'm looking for something that would be enough for simple setup (it will be one movie 2xWUXGA displayed on curved wall) and also won't cost much. I know about SSD disk and memory, but the problem for me are processor, motherboard and graphic card. Can you recomend something for this setup?
  5. Hi, I'm trying to add a image proxy to my show. Manual says something like this: My case is the third one- I will need to replace the file later. So I added a proxy image to my show, with path in display computer and file transfer method set to manual (like on page 141). After updating show the image appeared. So now the later time has came, and I need to replace the file. The image have the same size (I mean resolution, not file size af course) and extension but after starting show (there is external control over tcp so after turning display computers over wol, the command is being sent to start the show), the image is still the old one. So am I doing something wrong, or do I not understand "manualy replaced at later time" in right way?
  6. Hi, So what would you recommend to change in this setup?
  7. Hi, I've been trying to set up a projection and blend it with 4 projectors. The playback is laggy. What can be the problem? I'm using computer with spec: i7 3770K 8 GB RAM Radeom R9 290 SSD hard drive 32 Gb I'm using windows 8 (due to other on-site requirements). I think that this setup is strong enough to cope with four projectors, but lag is big, wideo can stop for a second. What can be wrong with it?
  8. Hi, I have to make a geometric projection for 22 projectors. Curently I'm using computers that are much too week for this setup (6 computer with 4 output card- amd e6760 embedded). I need to choose something better. I know that I need powerfull procesor. But I also need to choose a grapic card but I have limited budget. Everywhere I seek I find a K5000 but it is quite expensive. I was thinking about amd radeon 7870 card. Have anyone tried it? Or mayby you have other solution?
×
×
  • Create New...