Jump to content

Search the Community

Showing results for tags 'Startup'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 6 results

  1. hi dear I want to make the show run automatically. I registered it in the Windows Startup Program and checked until Watchout appeared. But I wonder if it will be possible to play right here. Assuming there is no operator. I looked through the manual countless times and couldn't figure out where to put the parameter variable. Of course, if the time code is received from the outside, it will be executed immediately. But I would like to know if it is possible to run it alone. thanks regards
  2. hi dear Make watchout play whenever windows starts Can you set it up? and what i want is watchout I want it to play as soon as the window is launched. and the play continues I want to use a function that turns off at a set time. We turn on the power at 9 o'clock and at the same time the watchout run window appears. It was possible until it opened. But not play. I wonder how to make it play automatically. thanks regards
  3. Can anybody advise on the below please: Motherboard: Asus WS X299 Pro CPU: Intel Core i7 7800X, S 2066, Skylake-X, 6 Core, 12 Thread Memory: Corsair Vengeance LPX Black 16GB (4x4GB) DDR4 PC4-19200 (2400) O/S Drive: Samsung SM961 Polaris M.2, 256GB NVMe, MLC V-NAND, SSD PCIe Watchout Drive: Samsung 850 Pro 512GB 2.5" SSD, SATA III GPU: AMD 16GB WX9100 Radeon Pro, PCIe 3.0, GDDR5 DATAPATH VISION SC-SDI4 VIDEO CAPTURE CARD MS WINDOWS 10 PRO 64 Bit Windows has been stripped back to recommended setup following Dataton instructions. MS Windows Updated to 1709 (Build 16299.309) as of 27th March 2018. Latest AMD Driver as of 27th March 2018 (V.18.Q1.1). Still current. Running Watchout 6.2.2. Previously running 6.2.1 6x mDP to HDMI adaptors (Startech) to 1080P monitors running at 60Hz. Forced EDID has been used. Issue: When attempting to start using Watchpoint.exe on display systems, it will attempt to load and then fail, which will then restart via the watchdog and continue to go through the cycle but fail to start. When running WP.exe, this will take around 18 seconds to start but will actually start. Adding GPU scaling to each screen via Radeon Pro settings cuts load time to around 12 seconds and after 4 cycles through the watchdog, will then start the show when run via Watchpoint. When running 4 outputs, the screens seem to initialise quick enough under Watchpoint without causing the watchdog to kick in and restart the programme, but as soon as we go to 5 or 6 outputs, the time taken to initialise is too long and therefore, can cause the watchdog to restart the programme. This is happening on multiple systems of identical specification. The start-up is consistent and repeatable, as well as being identical between the two systems making a hardware fault very unlikely. Additionally, using different screen edids appear to impact the initialisation time, one edid with very flexible settings ( lots of colour depths, resolutions and refresh rates available ) took almost 45 seconds to initialise running WP.exe, subsequently putting watchpoint.exe into a restart loop. We also tried the gaming driver variant which is available to the WX9100 and this made little to no difference to the initialisation times for WP.exe. We found a forum post indicating that the TdrDelay and TdrDdiDelay registry entries be increased to prevent Windows from killing the graphics drivers too soon. However these registry entries were not present to edit, and adding them had no effect. This has also been seen on multiple other systems running more than 4 outputs at any one time and also on systems running W600 GPU, both at 1080 and 4K. Is there any way to resolve this and if not, is there something that can be done to extend the timeout of the watchdog so that everything has time to initialise?
  4. I have this problem with my Watchout display computers for a long time (Watchout 4.5.1 version). How can i make the watchpoint to start automatically once my computer finish booting up? I tried to reinstall the program, but it's giving me the same problem. Hope you guys can help me fix this problem. Thank you very much!
  5. Hello everyone! Just upgraded to v5 and working on configuring my setup. One problem I'm having is with the new startup script option for Watchout Display. I'm able to remotely power up/down the computers but I cannot get Display to launch at startup. When I go to edit the startup script, the file is empty. I looked through the documentation and did not see an answer. Any help would be appreciated, thanks!
  6. Whenever I startup the computer, and have the shortcut in the "Startup" folder, watchout starts, but then stops, leaves full screen mode and I get a message that reads: the project wasn't found "project name" The project file is in the "Shows" folder and if I load it into the Production software it runs perfectly fine. Any help is appreciated.
  • Create New...