Jump to content
Dataton Forum

Search the Community

Showing results for tags 'output'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 6 results

  1. Hello, I have 102 DMX lights that I have setup to be controlled using Output Tasks. I am using dmxLAN Node 1s on Artnet. I can control all lights with no problem. My issue comes in when some groups of lights (in example, hallway lights) needs to be continuously turned on. When I play the next output task (another set of DMX channels), the current running task/lights will flicker OFF for 2 seconds before it goes on again. In a nutshell, say, DMX 1 and DMX 2 will turn off for a while when i turn on DMX 3. But DMX 3 wont turn off when I play and light that has a lower DMX value. I hope
  2. Hi I have newly Built 2 Servers config: i9 7900x Processor Asus X299 Pro Motherboard 32 GB Ram G skill gaming samsung pro 860 SSD x3 amd Radeon WX7100 DATAPATH 4K Capture Card VISION-SC-HD4-+ My Watchout screen is fluctuating and losing connections,if I give 2 Outputs it works fine but if i Increase Outputs 3 or 4 As soons as i open Give “online Command” my displays starts flickering and starts losing connection ,It’s Going out & In My Output were are follows output 1-DP to HDMI active Connector & connecting to XGA Projector (10
  3. I am working with WO 5 and trying to send TCP commands to 2 Christie DHD800 projectors, but getting no response from the projectors. Sending Command: C0D$0D & C0E$0D on Port 3002 I also tried sending: Commands: SHUT1$0D & SHUT0$0D SHU0$0D & SHU1$0D Port 3001 and 10000 When I use telnet I have no problems sending the command C0D and C0E, (shutter mute and un-mute) Any thoughts on why the projectors are not seeing the TCP command when sending through WO? The network manual mentioned that the connection will be closed after 30 seconds. Do I nee
  4. Hi eveyone, I'm new here and not so familiar with projections: I'm making a video to be projected with 15 projectors in a 360 circular screen, so my output is a quite long video of 6346 pixels wide and I can't find a way to compress an .mp4 h264 video to deliver at this size. They keep asking me a single video but i can only split it into two files so i can compress it. My question is: is it possible to use 2 videos instead of a single one and align them inside Watchout right? I mean they don't really need it to be a single video right? Thanks guys!! Elia
  5. Hi everybody! I am building a multi-outputs machine based on your document: "WATCHOUT dpcspec-4U rack - March 2013 SB-E LGA2011 AMD FIREPRO.pdf" The only things different are the torque: processor / motherboard. I was offered the following material: Motherboard Supermicro X9SRA Proc Intel Xeon E5-1650 Based on your expertise, do you see any problem to choose this material? Thanks!
  6. Anyone out there available to help me with an audio question. I have 5.1 enabled in my 'Realtek' audio controls in the display machines control panel. I've tested the outputs and verified the audio. Now, my question is; how do you asscociate the proper display on my 4 head card to the proper audio output? These outputs are not numbered (instead they read - Side, Sub, Rear, Out etc...) I have v5 running ATI FirePro V7900. I have a WAV test file. However there arent ANY options in Watchouts GUI that allow me to direct what Audio file gets tied to what TRS output. I can drag the file to the scree
  • Create New...