[Down phenomenon after 25 minutes of watchout production]

I finally figured out the cause.

1. It had to do with the resolution.
We used 6 projectors.

However, the recommended resolution of the projector was 1920x1080 for 3 units and
 1920x1200 for 3 units.

Therefore, the output resolution was unified to 1920x1080.

Anyway, the first 4 days were fine.

Production started to shutdown on the 5th day. every 25 minutes

After the event, I tested it on an HD monitor in the office.
There were no problems at all.

The same problem occurred in Useed as well.
Useed is a Korea dealer.
We shared information.

They tested it with different graphics cards and the 3070 didn't have that problem.

No problem with any recommended resolution.

2. This also seems to be a problem with the w.o version. According to them, 
this symptom appeared only in Ver 6.*.* version.

Even if the recommended resolution and the w.o setting resolution are different,
 I think that shutdown should not occur.
Please refer to it in the next version.

 

[Down phenomenon after 25 minutes of watchout production]

Thanks for the reply.

I only backed up the mapping data and worked again.

And the video file is completely new and only one file
I did a test.

Still had the same symptoms.
(Then I think log files and cache files are irrelevant.)

I think it's another bug, how do you see it?

[Down phenomenon after 25 minutes of watchout production]

Down phenomenon after 25 minutes of watchout production

After setting the watchout 10 days ago, it was played without any problem.
The sauce was changed once a day.

And 3 days ago, the abnormal symptoms started.

Immediately after 24 minutes of watchout production
will be shut down.

We haven't figured out the cause yet.

These are the actions I have taken.
1. Test by version 6.6.5~6.6.7
2. Test by codec (HAP,H264,PROLESS, ..MOV,MP4..)
3. Windows Security Update
4. Test this file in another production..(same symptom)
5. Tested this file on my laptop.. (This works fine)
6.NVIDA VERSION No problem..

Videos and files are attached below.
Seeking advice from people who have experienced these symptoms.

[Can I check the progress and remaining time?]

Hi dear

I want to know exactly how long each source on the timeline is running and how much time is left. Is this possible?

It's simple, but it's necessary.

 

[Is it possible to play by receiving external TCP/IP input?]

hi dear

I want to write a protocol to control the watchout externally.

I'm trying to find a way to take control from anywhere with the internet.

Thank you always for your replies.

[Real-Time LTC Timecode Generator]

Hi Tim

Can this be used in watchout?

Is it possible to add more cuelists?

 

[Geometry file save ?]

Thank you.
If I follow your advice, it works.

The order of saving geometry.

[Geometry file save ?]

Hi dear

Is there a way to save this to a file after setting the geometry?
I would like to know if it is possible to reload later.

Please advise. 

Thanks.

[Geometry file save ?]

Hi dear

Is there a way to save this to a file after setting the geometry?
I would like to know if it is possible to reload later.

Please advise. 

Thanks.

[Is it possible to autoplay by itself?]

thank you for your response.
I found an easier way to solve this problem.

I was using a macro program.
When the watchout launch window pops up,
 you can use a macro program to play by pressing the space bar.
It would be good to add this function to the next version.
This function is required for fixed installation.

thank regards

[Is it possible to autoplay by itself?]

hi dear

I want to make the show run automatically.

I registered it in the Windows Startup Program and checked until Watchout appeared.

 

But I wonder if it will be possible to play right here.

Assuming there is no operator.

 

I looked through the manual countless times and couldn't figure out where to put the parameter variable.

 

Of course, if the time code is received from the outside, it will be executed immediately.

But I would like to know if it is possible to run it alone.

 

thanks regards

[Make watchout play whenever windows starts]

hi dear

Make watchout play whenever windows starts

Can you set it up?

and

what i want is watchout

I want it to play as soon as the window is launched.

 

and the play continues

I want to use a function that turns off at a set time.

 

We turn on the power at 9 o'clock and at the same time the watchout run window appears.

It was possible until it opened.

But not play.

I wonder how to make it play automatically.

 

thanks regards

 

 

 

[How to use output string Cue ? I want to control the Barco Project power through tcp/ip]

thank for jfk

I did it your way.
But it's not working and I don't know why.
Because pj link port 4352
Port 4352 was used.
Do I need to do something else before running watchout production?

[How to use output string Cue ? I want to control the Barco Project power through tcp/ip]

hi dear
I turn the projector on/off through string output
I'm going to do it.
The projector is a Barco GW60-W7.
It works fine with PJ Link.
But I wonder if this can work via production pc string ouput
I want to know.

IP address and IP Port are set correctly.
However, when applied to the timeline, it is not working.

How to write the command in String Cue Data to send
I do not know.

The on command in pj link is " send %power 1 ".

I was wondering how to apply this to Data to Send.